Vista Ademco -10SE Guía para resolver problemas descargar pdf (Pagina 92)

TO PROGRAM

SYSTEM STATUS

AND RESTORE

REPORT CODES

(*59 -76, & *89)

The following is a set of guidelines to be used for progr

amming report codes.

The actual digits that you enter depend upon the particular installation, and

should be in agreementwith you and the central station officereceiving the

signals. Use theseguidelinesto program this entire section.

With a 3+1 or 4+1 Standard Forraati Enter a codein the

first box 1–9, ~

B, C, D, E, or F. Enter “#+10 for A (this reports a “O” on some receivers),

“#+11”for B, “#+12”for C, “#+13 for D, “#+14”for E, “#+15” for F.

An entqy of “O in the

first boxwiIl disablea report.

An entry of “O”in the secondbox will result in automatic advance to the

next field when programming.

With an Expanded or 4+2 Formati Enter codesin

both boxes(lst and 2nd

digits) for 1–9, or A-F, as describedabove.

An entry of “O in the

first boxwill disablea report.

An entry of “O”in the

second box will eliminate the expanded messagefor

that report.

With Ademco Contact ID Reporting: Enter a digit in the first box to

enable the zone to report. Use a different digit for each zone until you have

used up available digits. If the number of zones exceedsthe number of

available digits, beginwith digit 1 again. This is an “enabling”codeonly and

is not the actual codesent to the cential station office.Entries in the second

boxeswill be ignored. For systemstatus(non-alarm) codes,enter a “1” in the

first box for all the systemconditionsyou want to send to the centml station.

An entry of “O”inthe

first box will disablethe report.

SYSTEM STATUS *59 _ -OR REpORT CODE (See ~x above.)

REPORT CODES

❑

(*56456)

If the systemis armed and an Entry/Exit or Interior zone is still open

after the exit delay time has expired, an alarm will sound at the

keypad and external sounder (keypad also displays “Exit Alarm”). If

the system is disarmed before the end of the entry delay that

immediately follows, the alarm sounding will stop and no message

will be sent to the central station. The keypad will display CA

(fixed-wordkeypads)or CANCELLED MAR.M (Alpha keypads).

If the system is not disarmed before the end of the entry delay

mentioned above,and an Entry/Exit or Interior zone is stiIl open, an

‘exit alarmm message will be sent to the central station if an

Exit Error Report code is selected in this field. The keypad will

display EA (fixed-word keypads) or EXIT ALARM (Alpha keypads),

and the alarm sounding will continueuntil the systemis disarmed (or

timeout occurs).

An “Exit Alarm” conditionwill alsoresult if a fault occursin an exit or

intenor zonewithin 2 minutes following the end of the exit delay, and

an “exitalarm” messagewill be sentto the central station.

If ContactID format has been programmed, the messagewill contain

the zonenumber and error code374 (Troubl~Exit Error) to define the

alarm as an Exit Error (rather than E/E or Interior). If 4+2 format is

used, the digit enteredin this field will be sent followedby the second

digit ofthe programmed alarm codefor that zone. If 3+1 or 4+1 format

is used, only the digit enteredin this field will be sent. This message

will go to the Primary Phone No. Under any of these conditions, no

Restoremessagewill be sent.

If “O”is enteredin this field, no specialmessagewill be sent, only the

regular alarm and alarm restorecodefor the zone.

*60

TROUBLE REPORT CODE (Seebox above)

*61

BYPASS REPORT CODE (Seebox above)

-92-

1 2 ... 87 88 89 90 91 92 93 94 95 96 97 ... 119 120

Comentarios a estos manuales

Sin comentarios

Vista Ademco -10SE Guía para resolver problemas Pagina 92

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Vista Ademco -10SE