Vista Ademco -10SE Guía para resolver problemas descargar pdf (Pagina 70)

For selectionof the next word (e.g.,DOOR), repeat step3, as follows.

Press key [3] until the fist letter of the next word appears (e.g., “D”).

Then press [6] to display the first available word beginning with that

letter (e.g. DAUGHTERS). Press [3] repeatedly until the desired word

(e.g., DOOR) appears.To acceptthe word, press [6], which togglesbackto

the alphabet list.

When all desired words have been entered, press [8] to store the

descriptionin memory.

Enter *NN, where NN is the next zone that You want to review or for

which you want to program a descriptor.To m~di@ the descriptor,enter

*NN again. To exit this mode, press“*oO”.

Adding Cuetom Words (will not be annundated by 4285 Voice Module)

You can add up to five installer-defied words canbe addedto the built-in vo-

cabulary. Each of the five “words” can actually consist of a “word string” of

one or more words, but no more than ten characters can be used for each

word or word string.

[s]

[11

[6]

[8]

Adv=ces through the

alphabetin ascending

order.

Moves through the

alphabetin descending

order.

Selectsdesired letter;

movescursoronespace

toright.

Movescursoronespace

toleft.

Inserts a spaceat the

cursorlocation,erasing

any characterlocated

there.

Savesthe newwordin

thesystem’smemory.

Perform steps 1, 2, and 3 of Programming the Descriptors on a

previous page.

Select CUSTOM WORD mode (enter “1”) when the prompt CUSTOM

WORD ? is displayed.

Enter the number ([1]–[5]) of the custom word or word string to be

created (for example, if you are creating the first customword or word-

string, enter [1], for the

second, enter [2], etc.).A cursor will now appear

at the beginning ofthe secondline.

One

of two methods of entering the custom word’s characters can

now be used (refer to the CHARACTER LIST of letters, numbers, and

symbols on a followingpage):

Method 1:

Press the [#]

key, followed by the two-digit entry for the W letter you

would like to display (e.g., [6][5] for “A”),

or...

Method 2:

Use the [3] key to advance through the list of symbols, numbers, and

letters.Use the [1] key to movebackthrough the list.

When you have reached the desired character,press [6] to selectit. The

cursor will then moveto the right, in positionfor the next character.

Repeat steps3 end 4 to createthe desired word(s). Note that the [4] key

can be used to move the cursor to the left, if necessary,and that key [71

can be used to enter a blank (or erasean existing character).Remember,

no word or word-shing can exceed10 characters.

Press the [81key to savethe customword(s) and return to the “CUSTOM

WORD ?-displiy.

Repeat steps 2-5 for other custom words to be entered. To change a

customword,just overwrite it. If no more are to be entered now, press [0]

to return to the Descriptor entry. The custom word(s) will be

automatically addedto the built-in vocabulary.

When zone descriptors are being entered as described in step 6 of

Programming the Descriptors, the customword numbers are 250 to 254

for words 1 to 5 respectively.

When being entered as described in step 3 in Alternate Method For

Programmhg Zone Descriptors, eachword will be found at the end of the

group of wordsthat begin with the sameletter as it does.

-70-

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 ... 119 120

Comentarios a estos manuales

Sin comentarios

Vista Ademco -10SE Guía para resolver problemas Pagina 70

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Vista Ademco -10SE