Vista Ademco -10SE Guía para resolver problemas descargar pdf (Pagina 80)

TO PROGRAM

SYSTEMSTATUS

AND RESTORE

REPORTCODES

(*59-*76,&*89)

The following is a setof guidelines to be used for programming report codes.

The actual digits that you enter depend upon the particular installation, and

should be in agreementwith you and the cenlmd station officereceiving the

signals. Use theseguidelinesto program this entire section.

With a 3+1 or 4+1 Standard Forma* Enter a codein the first box 1–9, A,

B, C, D, E, or F. Enter “#+10” for A (this reports a “O” on some receivers),

“#+11”for B, “#+12”for C, “#+13” for D, “#+14”for E, “#+15”for F.

An entry of “O” in the firstbox will disablea report.

An entry of “O”in the secondbox will result in automatic advance to the

next field when programming.

With an Expanded or 4+2 Forrnati Enter codesin

both boxes(lst and 2nd

digits) for 1–9, or A–F, as describedabove.

An entry of “O’ in the

first boxwill disablea report.

An entry of “O in the

second box will eliminate the expandedmessagefor

that report.

With Ademco Contact Ill Reporting Enter a digit in the first box to

enable the zone to report. Use a di&erent digit for each zone until you have

used up available digits.

If the number of zones exceedsthe number of

availabledigits, beginwith digit 1 again. This is an “enabling”codeonly and

is not the actual codesent to the central station office.Entries in the second

boxeswill be ignored. For systemstatus (non-alarm) codes,enter a “1” in the

fist box for all the systemconditionsyou want to sendto the central station.

Au enlny of “Oin the

first box will disablethe report.

Press *59 EXIT ERROR REPORT CODE

fieSS *6O

fieSS *61

-S *62

Press *63

Press w

Press *65

If “O”is entered in this field, no speckd messagewill be sent,

only the regular alarm and alarm restorecodefor the zone. If a

non-zero codeis entered, this messagewill be sent if an ah-m

occurswithin 2 minutes after the end of the Exit time.

Refer to

Section 19. DATA FIELD DESCRIPTIONS for a

detaileddestiption of this option.

Field *59 entry note: The 2nd digit is automatically sent as

the 2nd digit of the zone alarm report codeprogrammed in * 56,

if expandedor 4+2 reporting is selected.

TROUBLE REPORT CODE

I-l_J

Thiswill

be sent if a zone goesinto trouble.

BYPASS REPORT CODE

Thiswill

be sent when a zoneis manually bypassed.

AC LOSS REPORT CODE

Reportawith Partition 1 Subscriber No. Timing of this report is

random with up to a 4-hour delay. If AC restores before the

report goesout, there is no AC restorereport.

LOW BAT REPORT CODE

IJ_J

This will be sent when a low battery condition exists in the

system’sstandby battery. Reports with Partition 1 Subscriber

No.

TEST REPORT CODE

LLl

This

is sentperiodicallyto testthat the communicatorand phone

lines are operational (Ilequency of report is selected in field

*51). Reportswith Partition 1 SubscriberNo.

OPEN REPORT CODE

Part’n lo Part’n 2 ❑

This is sentupon dis

arming of the system. 2nd digit= User No.,

if expandedor 4+2 reporting is selected.

-60-

1 2 ... 75 76 77 78 79 80 81 82 83 84 85 ... 119 120

Comentarios a estos manuales

Sin comentarios

Vista Ademco -10SE Guía para resolver problemas Pagina 80

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Vista Ademco -10SE