Vista Ademco -10SE Guía para resolver problemas Pagina 100
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
The installer programs the 4-digit Installer Code initially as part of the
programming procedure. The factory default Installer codeis “41-1-2”, but
may be changedin field =0.
The Installer code is the only codethat can enter programming
mode and
also, in normal operation mode, is used to enter the Master code for each
partition, which allows accessto the normal functionsof the system.
See
Section 4. MECHANiWS OF PROGRAMMZZVGfor information on exiting
the programming
modevia fields*98 or W9.
Master Code
In normal operation mode, the Installercodeis used to enter the 4-digit
Master security code for each partition, using
tke keypad connected to
Partition 1:
To enter the Master code for Partition 1, enter
I
Installer Code + [8]+ [01] + desired4digit Master codefor Partition 1
I
To enter the Master code for Partition 2, entex
Installer Code + [81+ [02]+ desired4digit Master codefor Partition 2
SecQtldary Ueer codes
In normal operation mode,
each partition’s Master security code can be
used to assignup to 14 secondary4digit securitycodesfor that partition. It
can alsobeused to remove secondarycodesfrom the system(individually).
To assign (or change) a Secondary security code, enter (via patiition ’s
kmmd):
Partition’sMaster Code + [CODE key]+ User # (03-16)
+ desiredSecondaryCode
I
Notes: ●
●
●
●
●
●
The systemwill emit a single beepwhen each secondarycode has been suc-
cessfullyentered.
To delete a Secondmy securi~ code, enter (via partition’s keypad):
Partition’s Master Code + [CODE key]+ User # (03-16)
All Master and Secondary security codespermit accessto the system for
-, diS-, e~.
The installer codecan disarm the systemonly ifit was used to arm it.
User codeNo. 15 is a ‘%abysitteflcode,i.e., it can disarm the system only
ifit wasused to arm it.
User codeNo. 16 is the Duress code.When this is used to perform any
systemoperation, a specialcodeis sent to the monitoring station. Insh-uct
users to be carefbl not to use this codefor normal usage.
If a secondarycodeis inadvertently repeatedfor different users, the lower
user number will take priority.
Opening and closingreports are sent for the Installer codeas No. 01, with
the appropriate subscribernumber. Each Master codeand set of seconday
user codes are sent as Nos. 02, and 03-16 respectively in Contact ID
format (with the appropriate subscribernumber); in 4+2, it is l–F, T“ for
anything greater than 14;keyswitchwill report asuser “O”.
-100-
- VISTA-20 1
- Heet-ktiited Detecbs 2
- 20. REMOTE PROG 5
- LIST OF FIGURES 6
- HOW TO USE THIS MAIUWiL 7
- Enter Zn Num 8
- (00 = Quit) 8
- “ - I,NciMiNGiE,co,,N 15
- IIIiIiII 16
- EarthGroundCkmections 16
- AusPower From 17
- SUPPLEMENTARY 19
- POWERSUPPLY 19
- TERMINALSTRIP 19
- SeCtiOIl 20
- ● g Mode 21
- Hard-Wined Zones 22
- ColnmonCharacierietics 22
- GLASSBREAK 24
- DETECTOR 24
- Rogmmdng iiard-Wmed Zones 25
- RESPONSE 28
- 04= Interior Follower 29
- General Information 32
- InstaUationAdvisories 33
- Instalbg the 5SOOTM Module 34
- 5800 Series Transmitters 34
- Programming 36
- Relay activation) 37
- 5800 Saks Tr 40
- Alsod= *O 40
- APPENDIX 40
- SHOWN SEr FORHOUSEiO#30 41
- 2s on on 41
- 4204 and 4229 Reky Modules 42
- Powerline Carrier devices 43
- TERMINAL 4142TRCABLEWIRE 44
- 4 (sync) 44
- Figure 15.4300 Transformer 44
- Wdng Comsect.ions 44
- ● TROUBLE 45
- STOP (STP): 46
- =E=lkey’mn”ue 48
- Inetalbg the Voice Module 50
- 1~1 [..~’=-rra i 52
- This will 53
- Compatible Soamdere 55
- Sounder (kUBdOM 56
- External Sounders 56
- Testing the Sounder 57
- 7720PLUWS20 58
- Installing the Keyswitch 59
- ,0Z.7PH5 60
- RosI--@3 For men-o~e K-* 61
- ,[07 ResponseTimel[l 62
- __Jm “.nsLAYuanu I 64
- ‘1 II II 68
- CHARACTER (ASC~ CHART 71
- “’”playd” 73
- KISSOFF ITRANSMITTIMEI 75
- RARARA(RA)4 76
- I 606 IAAv to follow I 77
- Communication R 78
- Introduction 78
- ❑ psrtition2 ❑ 85
- ❑ Partition2 ❑ 85
- Zone me (ZT) for 86
- ❑ %rt?n2 ❑ 87
- Type “1” 90
- 24. SilentBurglary 90
- (Default = [1] 90
- Enter’1” or “2” 90
- Press [*] to advanoe to 90
- ZiEF=l 4“ 91
- Remote Prog 97
- Test Px●cedure 98
- TO THE INSTALLER 99
- Keypad Functions 101
- ● A display of “EXIT 102
- Trouble Conditions 103
- Infomnation 103
- SYSTEM (including Wireless) 104
- 588M5882 104
- (5817) programmed 104
- XdfildiOIliIE 105
- CCOIIkeCtiOTM 105
- CONTAC’?7NG TECHNICAL SUPPORT 106
- Specifkations 108
- X 1“ D (146mmX 1211nmX 26mm) 109
- - NOTES 112
- THE LIMITATIONS OF THIS ALARM 113
- LIMITED WARRANTY 118
- Figure 22. VISTA-20 SUMMARY 119
- OF CONNECTIONS 119
- 1995 PMWAY CORPORATION 120
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Vista Ademco -10SE
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales