Vista Ademco -10SE Guía para resolver problemas descargar pdf (Pagina 86)

*27

POWERIJNE CARRIER DEVICE (X-1O) HOUSE ID

❑

Powerline Carrier devicesrequire a House ID. This field identifies

this houseID to the control.

If PowerlineCarrier devicesare used, they are selectedin field * 80.

House ID is enteredin followingmanner:

0= A,1=B,2=C, 3= D,4=E,5=F, 6= G,7=H,8=I,9=J,

#+10= ~#+ll=L, #+12= M,#+ 13= N,#+14=0, #+15=P.

Default is O.

*28

VOICE MODULE PHONE CODE

The use of a 4285 Voice Module (can be used in Partition 1 only)

requiresa 2-digit code.

Enter a 2-digit phone accesscodeas follows: For first digit, enter

any any digit from 1 to 9; for second digit, enter # +11 for “*”, or

# +12 for “#”.

ExampZe: If desiredaccesscodeis 7*, 7 is the first entry, and # + 11

(for *) is the secondentry.

*9 OUTPUT TO LONG RANGE RADIO (No. 7720 PLUW7820)

❑

If output to LR.R is selectedhere, all messagesthat are programmed

to go to the primary telephoneline receiver wiIl also be sent to the

7720 PLUS or 7820radio. Thesemessageswill always be in Contact

ID format (not affected by entry in field *48). The data line is

supervised as well as certain functions in the radio. If

communication is lost or a trouble develops, a message will be

attempted to be sent via both radio and telephone to the central

station.

Note: Normal trouble restorereport (*71) is sent on restore of the

condition.

Entry is first digit of Trouble Dialer Repo~ enter Trouble code1-9,

B (# +11), C (# +12), D (# +13), E (# +14), or F (# +15). The 2nd digit

of Trouble Dizder Report is automatically the 2nd digit fkom field

*60. For UL installations, Long Range Radio must be

disabled (enter “O”).

Note: The Radio should be programmed for deviceaddress 3 on the

keypadlines.

*3O

KEYSWITCH ENABLE

•1

This field must be enabled (enter 1) if using a keyswitch. The

keyswitchmust be connectedto zone 7, which can then not be used

for any other purpose.

Default is O (no keyswitch).

●

If keyswitchis enabled,in menu mode *56 the Zone me (ZT) for

‘zone 7 will show “77”, and the zone will not be accessiblefor

progr

amming.

If the 4146 kewnvitch is used

with onlv Red and Green LEDs

connected(no iock switchand tamper

&tch) to simply provide

an armingkeady

status indicator panel, zone 7 can then be used

as a hard-wired protectionzone, provided you do not enable

this field.

ZONE SOUNDS AND

*32

SINGLE ALARM SOUNDING PER ZONE

(per armed period) ❑

(*=:

This field limits alarm soundingto once per arming period for a given

zone. Enter 1 for yes; default is

O (no). Enter 60- for UL

installations.

*33

FIRE SOUNDER TIMEOUT

•1

This field determineswhether the external sounder will shut off after

time allotted, or continue until manually turned off. Enter O for

soundertimeout, or

1 for no timeout. Default is O.

Enter ‘@B for UL installations.

1 2 ... 81 82 83 84 85 86 87 88 89 90 91 ... 119 120

Comentarios a estos manuales

Sin comentarios

Vista Ademco -10SE Guía para resolver problemas Pagina 86

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Vista Ademco -10SE