Vista Ademco -10SE Guía para resolver problemas descargar pdf (Pagina 39)

Using The Tmnsmitter Sniffer Mode

1. Enter Installer code (4112)+ # + 3. This initiates a procedure that will

providea checkthat all transmitters have beenproperly programmed.

2. The keypad wilI display all zone numbers of wireless units programmed

into the system.Fault eachtianemitter in tumq causingeach oneto send a

signal, rather than let each transmitter send an automatic

supervisory signal. An automaticsupervisorysignal that is receivedin

this modewill bemisinterpreted as a low battery signal.*

As the system receivesa signal fkom each of the transmitters, the zone

number of that transmitter will disappear from the display. The

transmittersmay be checkedupon installation, or in an installed system.

Note: A transmitter not “learned”will not turn off its zone number.

3. When all transmitters have been checked, exit the sniffer mode

immediatelyby keying Installer code (4112)+ OFF.

* If oneormorelowbatterymessagesdoappearafterexitingthesniffermode,doone

ofthefd.lowing

A Faulteachzonethat is showinga lowbattery,then entera disarmsequence

(Code+ OFF) toclearthelowbatterydisplay,or..

B. Enterandexitthe programmingmode.Thiswill clearany lowbatterysignals

&ommemory.

~~p

To Either T

ermaneatly Remove A Zone From The System.

1. Enter the programming mode and press[*1[51[61.

2. Enter the zonenumber and press[*I. A summary display will appear.

3. Ress [*] again.

m ‘ess[*]timntiue

4. The “Zone Type” prompt will appear. Enter

[01[01.This setsthe zonetype to “Not Used”.

- “le’thezOne”

5. The next prompt will ask whether you want

‘Yes” vnll permanently remove the zonefkom

the system,while a “No”will disableit but re-

tain all data exceptthe original zone @pe. You can then go back to this zone

later and put backan activeZoneType to re-enableit.

A serial number that has been learned for a 5800 system will not be

deleted if the zone is temporarily disabled by answering ‘Non to the

prompt above.

If only the physicaltransmitter is to be removed or changed (i.e., its sefia.1

number deleted,as when replacing a unit that has a non-removable battery),

it can be done in *56 Mode, but we recommend using the *83 mode (in a

later sectionof this manual).

Deleting a Transmdt

“ erSerial Nmnber Froma~in x56 Mode

Abbreviated

Procedure:

~o~~ programming mode, press [*1[5][61to enter Zone Programming “

Then.enter the zone number, and press [*I mpeate~y ~fl the cursor iS

under the %mmed RF Input (L)” position. ~S is the spefic mPut

(loop)or button on the transmitter that has beenlearned for that zone.

En~ a [O]at this point, then press[*I.

A prompt “Delete S/N?” will appear.

Enter ‘Yes”to deletethe existingserial number from the system.

Note that the other programmed values for that zone will not be deleted.

This will allowyou to r~instate a new transmi

tter in its place.

A displayfor the next zone number will appear.To exit, enter “00 *“

Press*9 to exitthe programming mode.

-39-

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 119 120

Comentarios a estos manuales

Sin comentarios

Vista Ademco -10SE Guía para resolver problemas Pagina 39

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Vista Ademco -10SE